碳化钒析出对X80管线钢焊接热影响区韧性的影响

通过Gleeble-3500热模拟机对钒(V)含量分别为0.06%和0.02%的X80管线钢进行了峰值温度为1350℃和750℃的焊接热模拟试验,利用硬度计和光学显微镜(OM)分别分析了焊接热模拟试样硬度和试样中马氏体-奥氏体岛状组织(M-A)的数量、尺寸和形貌。利用透射电镜(TEM)对母材、粗晶区和部分相变区中粒子析出进行了表征。结果表明,与0.02%含V量X80管线钢相比,0.06%含V量的X80管线钢由于V含量较高,在受到多道次焊接热循环影响时,部分相变区有较大量碳化钒(VC)粒子析出,明显阻碍位错运动,使其强度明显提高的同时脆性增大、塑性变形难以进行,导致其焊接热影响区韧性下降。     

Improved 3D image segmentation for X-ray tomographic analysis of packed particle beds

Although High Resolution X-ray Micro Tomography (HRXMT) has been developed in the past years for the 3D analysis of multiphase mineral particles in packed particle beds, image analysis of fine and/or high-density/high atomic number particles has been limited by existing segmentation algorithms. In this regard, a feature-based segmentation algorithm has been developed and demonstrated to provide a more accurate image processing method for the analysis of such multiphase particle populations. Based on this improved segmentation algorithm, image analyses of packed particle bed samples were compared to segmentation by traditional 3D watershed segmentation. Also, calculation of particle number using optical microscopy, together with a digital camera, was accomplished to validate feature-based segmentation. Detailed procedures and results for sample preparation, image analysis and validation are presented and discussed.     

Abrasive waterjet micro-machining of channels in metals: Comparison between machining in air and submerged in water

Abrasive water jet technology can be used for micro-milling using recently developed miniaturized nozzles. Abrasive water jet (AWJ) machining is often used with both the nozzle tip and workpiece submerged in water to reduce noise and contain debris. This paper compares the performance of submerged and unsubmerged abrasive water jet micro-milling of channels in 316L stainless steel and 6061-T6 aluminum at various nozzle angles and standoff distances. The effect of submergence on the diameter and effective footprint of AWJ erosion footprints was measured and compared. It was found that the centerline erosion rate decreased with channel depth due to the spreading of the jet as the effective standoff distance increased, and because of the growing effect of stagnation as the channel became deeper. The erosive jet spread over a larger effective footprint in air than in water, since particles on the jet periphery were slowed much more quickly in water due to increased drag. As a result, the width of a channel machined in air was wider than that in water. Moreover, it was observed that the instantaneous erosion rate decreased with channel depth, and that this decrease was a function only of the channel cross-sectional geometry, being independent of the type of metal, the jet angle, the standoff distance, and regardless of whether the jet was submerged or in air, in either the forward or backward directions. It is shown that submerged AWJM results in narrower features than those produced while machining in air, without a decrease in centerline etch rate.     

Evaluation of particle recovery from microalgae

Coccoliths are micro-structured biomineral particles found in cell protective covering layers of coccolithophore species. They are mainly composed of CaCO₃ and their individual crystal entities are arranged in such a way that they construct complex and unique structures. This complexity is found down to the individual particle level and appears to have promising properties to offer. This study focuses on the essential step prior to any kind of implementation, which is the recovery of the material. It summarizes cleaning protocols found in literature, compares them for the first time for the same freshly cultivated material and addresses challenges that still need to be overcome. Further, it highlight the advantages and disadvantages of the best cleaning protocols, suggests optimizations with promising results and uses size distribution measurements to analyse the recovery efficiency. To that end, further characterization techniques, new for coccoliths, are introduced and used to improve our current knowledge of the particles behaviour.     

Characteristics of pigments,modification, and their functionalities

Novel treatments of pigments with inorganic materials have tremendous industrial and commercial prospects. Specific treatment of pigment has a marked effect on its behavior during application. The treatment allows a broad modification of the surface characteristics of pigment particles which leads to improved functionalities. Surface modification of pigments is achieved via coating, polymerization with modifying reagent, treatment with derivatives or polymers, which alter either the optical, conductivity or dispersibility during processing and application. These and many other distinguishing factors that affect the characteristics of pigments such as the class, crystal structure, particle morphology, particle size, hiding power, pigment volume concentration, surface character, and surface treatment have been reviewed. Various organic pigments such as those from fungus and bacteria, and the various families of pigment types such as metallic pigment, light interference, and diffractive pigments which presents decorative quality such as leafing, nonleafing, pearlscent, and Fabry‐Perot effects on substrates have also been reviewed in addition to those from inorganic sources with emphasis on the structure and physiochemical modifications using metal and nonmetal Ions.     

α径迹法用于分辨高浓铀和Pu微粒的方法研究

擦拭样品微粒分析技术是核保障环境样品分析的一种主要手段，从大量灰尘颗粒中识别并定位含高浓铀（HEU）或含Pu微粒是微粒分析首先需要解决的问题。本文以HEU和Pu微粒为研究对象，建立了用于微粒α径迹测量的样品制备方法，采用CR-39固体径迹探测器为α径迹探测器，测量了不同蚀刻时间2种微粒产生的α径迹星的径迹参数。结果表明：可通过测量径迹短轴与曲率直径并作图来分辨HEU和Pu微粒，该方法对于蚀刻时间大于10 h的微粒径迹星，均能明显分辨，对于径迹非常密集的径迹星，也能准确分辨。